Hifiverse

Endstufen Stereo - Soulnote A-3 Core

Beschreibung, Bilder, technische Daten und Spezifikationen

Soulnote A-3 Core
Bildquelle - (c) Soulnote

The A-3core is a stereo power amplifier from Soulnote of Japan. Soulnote describes it as the A-3 integrated amplifier converted to a power amplifier. It comes in silver or black, with H versions for 220 V and T versions for 115 V mains.

Key specs that matter

Rated output is 120 W + 120 W into 4 ohms. Total harmonic distortion is 0.27% (1 W, 8 ohms) and frequency response is 2 Hz - 200 kHz (±3 dB, 1 W, 8 ohms). Input sensitivity is 480 mV, input impedance is 24 kohms and gain is 22 dB. Power consumption is 180 W, or 86 W at idle. Maximum external dimensions including spike feet are 454 x 189 x 435 mm (W x H x D), and weight is 29 kg. A spike board, spikes, a spacer for floating the spike board and a power cable are included.

Engineering and use context

Voltage amplification uses a newly developed high-gain-to-GND single-stage Type-R circuit, fully balanced and without negative feedback. Naked foil resistors are used for all resistors involved in amplifier operation. Each channel has a single push-pull SEPP output stage with the TO3 metal can bipolar transistor of the M-3, in a 4-stage Darlington configuration with TO3P transistors in the driver and pre-driver.

Instead of a conventional heat sink, a lightweight copper plate is the main heat sink and also the bus bar that supplies the TO3 transistors. Their terminals pass through the bus bar and are mounted directly on the board underneath, so no wiring and no insulation sheet are needed. This bus bar heat sink is physically independent of the chassis and joins the power supply board and amplifier board into one block.

Left and right channel GNDs are completely separated, using the technology of the P-3 preamplifier, and the enclosure is ungrounded. Soulnote reaches this with simple non-NFB circuits, optimised board artwork and minimised high-current loops. The supply GND of each channel is anchored to side metal insulated with ceramic washers.

Inside are two 700 VA unimpregnated toroidal transformers for left and right plus a control system transformer, all mounted vertically. Filtering uses 470 µF high withstand voltage foil capacitors and SiC rectifier diodes. Two large power relays switch the main transformers, while the front panel switch serves only the control sub-transformer. The amplifier block, terminals, AC inlet and covers are unfixed, and the block sits on a three-point lateral sliding structure with titanium sliders.

Pairing

A preamplifier with volume control is required. The matching Soulnote preamplifier is the P-3. Loudspeakers down to 4 ohms are within the rated load.

Alternatives

The M-3 and M-3X are monoblocks, so Soulnote lists no second stereo power amplifier.

Spezifikationen

  • Modellbezeichnung

    A-3 Core

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    24000

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    N/A

  • Ausgangsleistung (4Ω) (W)

    2 x 120

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    2

  • Obere Grenzfrequenz +/- 3dB (Hz)

    200000

  • Signal-Rausch-Abstand (dB)

    N/A

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    0.27 (at 1 W / 8 Ohm; without feedback, non-NFB)

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    454 × 189 × 435

  • Gewicht (kg)

    29

  • Offizieller Link