Hifiverse

Endstufen Stereo - Boulder 1162

Beschreibung, Bilder, technische Daten und Spezifikationen

Boulder 1162
Bildquelle - (c) Boulder

The 1162 is a stereo power amplifier of the Boulder 1100 Series, which also includes the 1151 mono power amplifier, the 1163 stereo power amplifier, the 1110 preamplifier and the 1108 phono preamplifier. Boulder Amplifiers was founded in 1984, and the 1162 with all of its casework is designed, machined and assembled in the company's 23,000 square foot facility in Louisville, Colorado. Its machined front panel depicts the topography of Flagstaff Mountain near Boulder.

Key specs that matter

Continuous power is 300 W per channel into 8 ohms. Peak power is 450 W into 8 ohms, 900 W into 4 ohms and 1,000 W into 2 ohms. At 300 W, THD is 0.002% (0.01% at 20 kHz) into 8 and 4 ohms and 0.003% (0.02% at 20 kHz) into 2 ohms. Equivalent input noise is 2.2 µV (20 kHz bandwidth). Magnitude response is +0.00/-0.04 dB from 20 Hz to 20 kHz, with -3 dB points at 0.015 Hz and 150 kHz. Voltage gain is 26 dB, and input impedance is 200 kohms balanced and 100 kohms unbalanced. Power consumption is 3,000 W maximum, 120 W idle and 10 W standby. Weight is 61.2 kg.

Engineering and use context

Boulder uses its Class-A Smart Current biasing circuit in the output stage. According to Boulder, it continuously monitors the output current drawn by the speaker and adjusts the bias through analog circuitry, giving class A performance without the drawbacks of traditional designs. More output devices are used than the 300 W rating requires, so each carries a fraction of the total output.

Dual toroidal transformers, one per channel, are DC filtered, float in a shielded, welded steel enclosure and are encapsulated in epoxy potting. Heat sinks are machined from a solid aluminium billet, and the feet contain constrained layer damping material.

The 1162 is a direct-coupled amplifier with a servo for zeroing out DC voltage. Its protection circuitry disconnects the loudspeakers on DC at the input and shuts down the output section on shorted speaker cables. Clipping in both voltage and current modes turns the front LED red, and a thermal cutout mutes the amplifier when the transistor cases reach 70°C, resuming at 60°C. Power relays under control of the supervising ARM processor limit the turn-on inrush current, and the Ethernet-enabled supervisor provides IP and HTML control. A 32 A IEC pre-terminated power cord is supplied.

Pairing

Inputs are balanced 3-pin XLR only. An unbalanced source connects through an RCA-to-XLR cable or the Boulder ABL2 input adapter. Two pairs of spade-only 6 mm binding posts per channel allow bi-wiring, and banana plugs and bare wire are not supported. The matching preamplifier is the Boulder 1110.

Alternatives

The Boulder 1163 is the other stereo power amplifier of the 1100 Series.

Spezifikationen

  • Modellbezeichnung

    1162

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    200000

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    100000

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    2 x 300

  • Ausgangsleistung (4Ω) (W)

    2 x 900

  • Verstärkung (dBu)

    26

  • Untere Grenzfrequenz +/- 3dB (Hz)

    0.015

  • Obere Grenzfrequenz +/- 3dB (Hz)

    150000

  • Signal-Rausch-Abstand (dB)

    N/A

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    0.002

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    N/A

  • Gewicht (kg)

    61.2

  • Offizieller Link

Weitere Komponenten