Hifiverse

Endstufen Mono - Emotiva XPA-1 Gen3

Beschreibung, Bilder, technische Daten und Spezifikationen

Emotiva XPA-1 Gen3
Bildquelle - (c) Emotiva

XPA-1 Gen3 is a monoblock power amplifier from Emotiva, built on the XPA Gen3 platform with one high-powered single-channel module. Emotiva designs, assembles and tests it at its plant in Franklin, Tennessee, and covers it with a five-year warranty. A pair is intended for a stereo or 2.1 music system, and three can drive the front left, centre and right channels of a 5.1 or 7.1 home theatre.

Key specs that matter

Rated output is 300 W RMS into 8 ohms (20 Hz - 20 kHz, THD <0.1%) and 600 W RMS into 4 ohms (THD <0.2%), with 4 ohms as the minimum load. Broadband frequency response is 5 Hz - 80 kHz (+0/-2 dB). THD+N is below 0.005% at 100 W, 1 kHz into 8 ohms. Signal-to-noise ratio is above 117 dB referenced to rated power and above 91 dB referenced to 1 W (unbalanced, A-weighted). Damping factor exceeds 500 into 8 ohms. Gain is 29 dB, and input sensitivity is 1.71 V for rated power into 8 ohms. Input impedance is 33 kohms balanced and 23.5 kohms unbalanced. Mains input is 100 - 250 V AC, 50/60 Hz, detected automatically, and maximum consumption with continuous full-power test tones is 1000 W. Dimensions are 432 x 203 x 483 mm (W x H x D, with feet), and weight is 15.2 kg.

Engineering and use context

The amplifier module is independent and fully discrete, with a dual differential, high current, short signal path Class A/B circuit. Power comes from a switched mode power supply using what Emotiva calls an Optimized Soft-Switch Class H power supply topology. Emotiva states that the SMPS gives improved efficiency and reliability and lower overall weight than a traditional linear supply. Construction of the Gen3 platform is fully modular.

Protection covers excessive operating temperature, shorted speaker connections, ground faults and other common fault conditions, and a resettable circuit breaker on the rear panel protects against AC line faults. On the front, a standby push button has a halo ring that changes colour between standby and on, and a blue status LED turns red on a fault. The rear panel carries RCA and XLR inputs, independently selectable, gold plated 5-way binding posts and a trigger input (5 - 12 V AC or DC) with a 12 V DC trigger output for loads up to 120 mA. Its heavy steel 4RU chassis has a milled aluminium faceplate.

Pairing

A preamplifier or AV processor with balanced or unbalanced outputs is required. Loudspeakers of 4 ohms or higher match it. The trigger connections allow switch-on together with a trigger-equipped preamplifier.

Alternatives

The XPA-DR1 is Emotiva's other mono power amplifier.

Spezifikationen

  • Modellbezeichnung

    XPA-1 Gen3

  • Eingangsempfindlichkeit (mV)

    1710

  • Eingangsimpedanz (symmetrisch) (Ω)

    33 000

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    23 500

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    300

  • Ausgangsleistung (4Ω) (W)

    600

  • Verstärkung (dBu)

    29

  • Untere Grenzfrequenz +/- 3dB (Hz)

    5

  • Obere Grenzfrequenz +/- 3dB (Hz)

    80 000

  • Signal-Rausch-Abstand (dB)

    >117

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    < 0.005

  • Maximale Leistungsaufnahme (W)

    100

  • Dämpfungsfaktor

    > 500

  • Abmessungen (mm)

    432 × 203 × 483

  • Gewicht (kg)

    15,2

  • Offizieller Link

Weitere Komponenten