Hifiverse

Endstufen Mono - Limestone PP1

Beschreibung, Bilder, technische Daten und Spezifikationen

Limestone PP1
Bildquelle - (c) Limestone

The PP1 is a class AB mono tube power amplifier from Limestone, the Croatian amplifier brand of WiM-Systems d.o.o. in Trnovec. Limestone combines retro styling taken from classic tube amplifiers with modern control electronics, and the brand name refers to the founder's father, a craftsman who made limestone by traditional methods. Every PP1 is hand-built, and its finish is made to order from a range of materials and colours. Prices start at EUR 10,000 excluding VAT.

Key specs that matter

Its output stage is push-pull with KT88 tubes. Power output is 45 W per channel. Frequency response is 30 Hz - 30 kHz (-3 dB), and THD is below 1% at 1 kHz. Signal-to-noise ratio is approximately 85 dB, with noise around 1 mV. Input sensitivity is 0.7 V RMS for the full 45 W. Output taps are 4 ohms and 8 ohms, on WBT gold-plated connectors. Dimensions are 250 x 250 x 550 mm (W x H x D), and weight is 18 kg.

Engineering and use context

Limestone builds the chassis from 1.5 mm stainless steel, and Kerrock decorative trims are applied to the exterior. Power-up and power-down are microprocessor-controlled, with delayed high-voltage activation at switch-on and capacitor discharge at switch-off. Protection circuitry guards the tubes against bias voltage failure.

A bias control system sets the operating point of the KT88 output tubes. Bias is adjusted with a high-precision Simpson analogue meter, and according to Limestone it can be set to match a variety of tubes. On the front panel are a VU meter, the power switch and a motorised ALPS potentiometer for volume. This potentiometer is adjusted automatically during startup and shutdown.

Pairing

A loudspeaker with 4 or 8 ohms nominal impedance connects to the matching output tap. A source or preamplifier delivering 0.7 V RMS is required for full output. The motorised ALPS volume control allows connection to a source with a fixed line-level output. A stereo system requires two units.

Alternatives

Limestone lists the PP1 as its only amplifier, so the brand has no other mono power amplifier.

Spezifikationen

  • Modellbezeichnung

    PP1

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    N/A

  • Ausgangsleistung (4Ω) (W)

    45

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    30

  • Obere Grenzfrequenz +/- 3dB (Hz)

    30000

  • Signal-Rausch-Abstand (dB)

    N/A

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    1.0

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    N/A

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    250 x 250 x 550

  • Gewicht (kg)

    18

  • Offizieller Link