Hifiverse

Endstufen Mono - Mark Levinson № 631

Beschreibung, Bilder, technische Daten und Spezifikationen

Mark Levinson № 631
Bildquelle - (c) Mark Levinson

The № 631 is the flagship amplifier of the Mark Levinson 600 Series - a fully differential, fully discrete monaural power amplifier in a floorstanding chassis. Mark Levinson, part of Harman, showed the series at High End Munich 2025 together with the № 626 preamplifier and the № 632 stereo amplifier, with deliveries from the fourth quarter of 2025. Each № 631 is priced at USD 40,000, GBP 37,999 or EUR 43,999, and a stereo system requires two units.

Key specs that matter

Rated output is 500 W RMS into 8 ohms (20 Hz - 20 kHz, below 0.3% THD), doubling into 4 ohms, and the amplifier is stable into 2 ohms. Frequency response is 10 Hz - 50 kHz (±0.2 dB) and 10 Hz - 200 kHz (+0.2/-1.5 dB). Signal-to-noise ratio is above 94 dB (ref. 2.83 V RMS). Input impedance is 900 kohm balanced and 450 kohm unbalanced, voltage gain is 26 dB, and input sensitivity is 142 mV for 2.83 V output. Each unit has one XLR and one RCA input and two pairs of Hurricane binding posts. Idle consumption is below 300 W. Dimensions are 522.7 x 305 x 521.9 mm (H x W x D), and weight is 83.5 kg.

Engineering and use context

Its output stage uses 24 discrete 15 A, 260 V, 200 W bipolar output transistors in TO-264 cases, each driven by its own 230 V, 70 MHz TO-126 driver transistor. Operation is Class A/AB with a selectable high-bias mode. Voltage gain and driver stages run in Class A, and the input and current transfer stages in pure Class A. Matched JFETs in a cascode form the input stage, followed by a folded cascode and current mirror. The signal path is direct-coupled, with no capacitors in it. Mark Levinson states that the high bias current and open-loop linearity allow very little feedback and make the circuit nearly immune to parasitic capacitances.

Power comes from a custom low-noise 2,000 VA toroidal transformer with separate secondary windings, discrete Schottky rectifiers and 250,000 µF of filter capacitance. The transformer is centrally located and structurally isolated. A modular architecture separates the low-level analogue circuitry from the power supply, critical components sit on rubber mounts, and the feet are vibration-damping and mechanically isolated. The Tectonic chassis is aluminium and steel, anodised black on a silver plinth, with a glass centre panel and red accent lighting.

Pairing

The matching preamplifier is the № 626. A balanced XLR connection is recommended. The two pairs of Hurricane terminals allow bi-wiring. Each unit requires a dedicated 15 A mains circuit.

Alternatives

The Mark Levinson № 536 is the earlier fully discrete monaural amplifier in the range.

Spezifikationen

  • Modellbezeichnung

    № 631

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    N/A

  • Ausgangsleistung (4Ω) (W)

    N/A

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Obere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Signal-Rausch-Abstand (dB)

    N/A

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    N/A

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    522.7 x 305 x 521.9

  • Gewicht (kg)

    N/A

  • Offizieller Link

Weitere Komponenten