Hifiverse

Endstufen Mono - Aavik M-880

Beschreibung, Bilder, technische Daten und Spezifikationen

Aavik M-880
Bildquelle - (c) Aavik

The M-880 is a mono power amplifier from Aavik, part of Audio Group Denmark in Aalborg. It refines the P-880 stereo power amplifier in a true mono configuration and is the result of a collaboration between engineer Michael Børresen and Flemming Erik Rasmussen. Every unit is hand-assembled in Aalborg and compared directly with a reference model.

Key specs that matter

Output is 400 W into 8 ohms, 800 W into 4 ohms and approximately 1,300 W into 2 ohms, with a damping factor above 1,000 into 8 ohms. THD is below 0.007% (10 W, 1 kHz, 8 ohms). Power consumption is below 0.5 W in standby and 150 W at idle. There is one single-ended RCA input, and gain is adjustable from 25 to 34 dB, with 31 dB as default. Speaker terminals accept spades and 4 mm banana plugs. Height is 794 mm, width 342 mm and depth 510 mm, and weight is 70 kg.

Engineering and use context

Aavik describes the output stage as pure Class A, re-engineered so that the bias stays 0.63 V above the required current throughout the signal cycle. According to Aavik, this keeps the stage in true Class A with less power dissipation than a conventional design. Each of the eight output transistor pairs has its own local reservoir capacitor bank placed next to the devices.

Power comes from four switching power supplies operating in power-factor-corrected resonant mode, which produce sinusoidal rather than square waveforms. Each is rated at 500 W and 20 A. Together they charge a local power bank of 266 mF that stores up to 1,050 J and supplies peak currents of up to 130 A. As demand rises, the operating frequency of the supplies rises too.

Noise rejection uses Ansuz technologies on the circuit boards - 112 active gold Tesla coils, 112 active square Tesla coils, eight circuits of third-generation analog dither and 14 gold anti-aerial resonance coils. Its square coils are etched onto the boards, with counter-coils on the underside. The base is a wood-based laminate between stainless steel plates, topped by an upper copper layer that carries the main enclosure. Inside, a fully copper chamber is the EMI/RFI shield. Each amplifier comes with four Ansuz Darkz Z3W resonance control devices, with ball bearings between zirconium discs. Two DC trigger connectors (5-24 V input) and an RS-232 port for firmware updates are on the rear panel.

Pairing

A preamplifier with RCA outputs is required. The matching control amplifier is the Aavik C-880. Two units are needed for stereo.

Alternatives

Aavik has no other mono power amplifier in its range.

Spezifikationen

  • Modellbezeichnung

    M-880

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    400

  • Ausgangsleistung (4Ω) (W)

    800

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Obere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Signal-Rausch-Abstand (dB)

    N/A

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    0.007

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    N/A

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    794 × 342 × 510

  • Gewicht (kg)

    70

  • Offizieller Link