Hifiverse

Endstufen Mono - Mola Mola Kaluga

Beschreibung, Bilder, technische Daten und Spezifikationen

Mola Mola Kaluga
Bildquelle - (c) Mola Mola

The Kaluga is a mono power amplifier from Mola Mola of Groningen, the Netherlands, and the original Mola Mola power amplifier that preceded the Ossetra. It is a class D design based on Ncore. Mola Mola describes it as an Ncore control topology built with the discrete signal processing stages also found in the Makua preamplifier. A Kaluga package contains two amplifiers, two power cords and two trigger cables.

Key specs that matter

Output power is 400 W into 8 ohms, 700 W into 4 ohms and 1200 W into 2 ohms. Gain is 28 dB, and unweighted signal-to-noise ratio is 128 dB. THD and IMD stay below 0.003% at all frequencies and power levels. Input impedance is 100 kohm. Output impedance is below 0.003 ohm at all frequencies, for a damping factor above 4000. Bandwidth extends from DC to 50 kHz (-3 dB). Each unit measures 200 x 110 x 335 mm (W x H x D) including the speaker terminals and weighs 7 kg. Power consumption is 30 W at idle and 1350 W at maximum output.

Engineering and use context

On the amplifier board, a Mola Mola specific design, the audio circuitry is reduced to the essential parts. Board-to-board connectors are not used. Star-quad cables are soldered directly into the circuit board instead. A separate circuit board carries the input stage, with the same discrete buffers as the Makua. In the output filter Mola Mola uses monolithic capacitors, chosen for their dielectric stability.

Its rear panel has a balanced XLR input and an unbalanced RCA input, selected by a toggle switch, and the RCA socket is covered by a black panel plug. Two pairs of Furutech binding posts are bi-wired directly to the amplifier PCB with Kubala-Sosna cable. A 3.5 mm trigger input accepts 2 - 15 V AC or DC. A single front button switches the amplifier on, and its LED is white in operation and dim red in standby. Cooling is by free convection along the sides and top. The auto-switching mains supply accepts 90 - 135 V or 180 - 270 V AC.

Pairing

A preamplifier with XLR or RCA outputs is required. The trigger input connects to the trigger output of the Makua preamplifier or the Tambaqui DAC. Its two pairs of binding posts allow bi-wiring.

Alternatives

The Ossetra is the later Mola Mola mono power amplifier, a full-bridge design based on the Trajectum class D platform.

Spezifikationen

  • Modellbezeichnung

    Kaluga

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    100 000

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    100 000

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    400

  • Ausgangsleistung (4Ω) (W)

    700

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Obere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Signal-Rausch-Abstand (dB)

    N/A

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    <0.003

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    200 x 110 x 335

  • Gewicht (kg)

    7.0

  • Offizieller Link

Weitere Komponenten