Hifiverse

Endstufen Mono - Emm Labs EMM Labs MTRX2 V2

Beschreibung, Bilder, technische Daten und Spezifikationen

Emm Labs EMM Labs MTRX2 V2
Bildquelle - (c) Emm Labs

The MTRX2 V2 is a mono power amplifier from EMM Labs of Canada, a re-imagined version of the MTRX2. EMM Labs describes it as a 1000 W Class A/B solid-state design, and it is designed and built in Canada. The original MTRX2 and the MTRX are listed as legacy products, so EMM's current power amplifiers are the MTRX2 V2 and the MTRS stereo amplifier. Price is available on request.

Key specs that matter

Power into 4 ohms is 1 kW RMS continuous (standard 120/230 V line voltage) and 1.3 kW dynamic (RS-490 EIA). Voltage gain is 30 dB. Frequency response is 0.1 Hz - 200 kHz at full rated power. Signal-to-noise ratio is greater than 120 dB (A-weighted). THD+N and IMD are each less than 0.015% (20 Hz - 20 kHz, full rated power). Slew rate is greater than 100 V/µs, and damping factor is greater than 200. Inputs are one balanced XLR (100 kOhm) and one unbalanced RCA (47 kOhm), and outputs are two sets of Furutech binding posts. Mains voltage is 100, 115 or 240 V, 50/60 Hz, set at the factory. Finishes are Silver and Black.

Engineering and use context

Ed Meitner curated the design himself. EMM Labs uses proprietary fully discrete circuit topologies, and the audio paths are fully balanced throughout. New in the V2 is the high-current Meitner Power Driver, and EMM Labs specifies the capability to deliver large transient currents and to drive complex loads down to 1 ohm. Its power system is a redesigned, latest-generation proprietary design.

Circuit boards are aerospace-grade ceramic PCBs, and internal wiring is Kimber Kable. Real-time protection mechanisms are built in.

Mains power enters through a 30 A 250 V three-pin IEC60309 inlet rated IP44, and a custom Kimber Kable 30 A power cable is supplied. An RS-232 communication port is provided. Each amplifier ships in a custom EMM Labs flight case. As a monoblock, one unit is needed per channel.

Pairing

A preamplifier with a balanced XLR output is the primary match, and the RCA input accepts single-ended sources. The EMM Labs PREi and the Meitner PRE are the brand's own preamplifiers. Its two sets of binding posts allow bi-wiring.

Alternatives

EMM Labs makes no other mono power amplifier in its current range.

Spezifikationen

  • Modellbezeichnung

    EMM Labs MTRX2 V2

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    100 000

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    47 000

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    N/A

  • Ausgangsleistung (4Ω) (W)

    1000

  • Verstärkung (dBu)

    30

  • Untere Grenzfrequenz +/- 3dB (Hz)

    0,1

  • Obere Grenzfrequenz +/- 3dB (Hz)

    200 000

  • Signal-Rausch-Abstand (dB)

    120

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    0,015

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    200

  • Abmessungen (mm)

    N/A

  • Gewicht (kg)

    N/A

  • Offizieller Link