Hifiverse

Endstufen Mono - Kora CSA 1200

Beschreibung, Bilder, technische Daten und Spezifikationen

Kora CSA 1200
Bildquelle - (c) Kora

The CSA 1200 is a pure Class A mono power amplifier from Kora of Toulouse, a company whose technical director is Bruno Vander Elst. Kora's CSA series comes in four versions, small or large, mono or stereo, and the CSA 1200 is the large mono model. Kora first showed the family in Munich in May 2025, and a pair of CSA 1200 costs about EUR 60,000.

Key specs that matter

Output power is 1 x 200 W into 8 ohms in pure Class A. A linear power supply with 560,000 µF of filtering powers the amplifier. Inputs are one RCA (unbalanced, 47 kohms) and one XLR (balanced, 20 kohms), selected by a switch on the rear panel. A rear GAIN potentiometer sets input sensitivity between 0.5 V and 2 V. Its aluminium and steel case in Mineral grey measures 420 x 660 x 260 mm and weighs 45 kg. A power cord, the user manual and a general information booklet come in the box.

Engineering and use context

Kora builds the CSA 1200 as a hybrid of Square Tube tubes and audio transistors, and the tubes are heated at each start-up. Its output is a pure Class A transistor stage in the strict sense - the signal is taken from the collector, and the transistors are biased in the middle of their characteristics, so they always operate in their linear zone. Crossover distortion is pushed back to the point of clipping. The large versions have 60 output transistors, and Kora states stability on complex, highly capacitive loads. This output stage is designed as a current source, like the anode of a power tube. Between the Square Tube and the power section sits a voltage/current converter made only of precision resistors, with no semiconductors.

Two bias levels exist - nominal current for full power and an economical mode at half the current. A rear CURRENT switch selects LOW, AUTO or HIGH, and in AUTO the amplifier changes to high current when the signal requires it and returns to low current in about ten seconds. At power-up the filter capacitors pre-charge slowly over a few minutes, and two green LEDs on the filter board confirm the supply is ready. An indicator on the back panel lights if mains polarity is reversed. On the front are a display and one knob that is turned to select and clicked to confirm.

Pairing

A preamplifier is required, and two units are needed for stereo. With the POWER switch on AUTO, the amplifier turns on when a signal reaches the input and returns to standby after one minute without one. The PHASE switch (0° or 180°) allows use in multi-amplified systems. Its terminals take 4 mm banana plugs or bare wire.

Alternatives

The Kora CSA 1150 is the small mono model of the same series, with 1 x 150 W into 8 ohms and 400,000 µF of filtering.

Spezifikationen

  • Modellbezeichnung

    CSA 1200

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    200

  • Ausgangsleistung (4Ω) (W)

    N/A

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Obere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Signal-Rausch-Abstand (dB)

    N/A

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    N/A

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    420 x 660 x 260

  • Gewicht (kg)

    45

  • Offizieller Link

Weitere Komponenten