Hifiverse

Endstufen Mono - Vinnie Rossi BRAMA Monoblock Power Amplifier

Beschreibung, Bilder, technische Daten und Spezifikationen

Vinnie Rossi BRAMA Monoblock Power Amplifier
Bildquelle - (c) Vinnie Rossi

The BRAMA Monoblock Power Amplifier is a mono solid-state power amplifier from VinnieRossi of Worcester, Massachusetts, the company that began in 2004 as Red Wine Audio. Together with the BRAMA Preamplifier and the BRAMA Integrated Amplifier it forms the second-generation BRAMA series, which debuted at AXPONA 2024. A pair costs USD 59,995.

Key specs that matter

Rated output is 300 W RMS into 8 ohms, 600 W RMS into 4 ohms and 1200 W RMS into 2 ohms. THD+N is below 0.1% (20 Hz - 20 kHz), frequency response is 5 Hz - 100 kHz (±0.5 dB) and signal-to-noise ratio is over 100 dB. Gain is 22 dB, input impedance 20 kohms and speaker output impedance below 0.01 ohms. On the rear panel are a balanced XLR line-level input, a Brama Link socket, WBT nextgen 0710-Ag binding posts and an IEC 320-C14 inlet with fuse holder. Mains input is 100-264 V AC (50-60 Hz) and idle consumption is 50 W. Each unit measures 475 x 406 x 140 mm and weighs 20.5 kg.

Engineering and use context

Its amplifier stage is a two-PCB stack. The upper board carries the fully balanced input and driver stages, and the lower board holds the Class AB MOSFET output stage, with components mounted on both sides of each PCB. VinnieRossi says the stack keeps signal and power paths short and isolates the input and driver circuitry from the output stage. Each rail uses three computer-matched lateral MOSFETs, mounted directly to the aluminium chassis, so the whole body is the heatsink.

DC offset is servo-controlled at the input stage to hold 0 V at the speaker outputs. Temperature and output current are monitored in real time, and the protection circuitry covers over-temperature and over-current faults. Power comes from a switch-mode power supply with active power factor correction, rated at 2400 W peak and enclosed in its own CNC-machined chamber, isolated from the audio circuitry.

Each chassis starts as a single billet of AL6063 aluminium alloy, machined on a 5-axis CNC machine, glass bead-blasted and anodised, with the logo laser-engraved on the top. This solid body encloses the supply and audio circuits and acts as an EMI shield. On the front, an output power gauge with an air-core movement sits behind sapphire glass in a polished stainless-steel bezel and reads RMS watts into 8 or 4 ohms. Every monoblock ships in an airtight hard case with custom foam, six latches, a retractable handle, wheels and an automatic air-pressure release vent.

Pairing

The matching preamplifier is the BRAMA Preamplifier, connected over balanced XLR and switched through Brama Link. Other preamplifiers connect over XLR, and Brama Link accepts a 12 V trigger. Loudspeakers down to 2 ohms are within its rated loads.

Alternatives

VinnieRossi has no other mono power amplifier in its current BRAMA and CANTA ranges.

Spezifikationen

  • Modellbezeichnung

    BRAMA Monoblock Power Amplifier

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    20000

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    0.01

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    300

  • Ausgangsleistung (4Ω) (W)

    600

  • Verstärkung (dBu)

    22

  • Untere Grenzfrequenz +/- 3dB (Hz)

    5

  • Obere Grenzfrequenz +/- 3dB (Hz)

    100000

  • Signal-Rausch-Abstand (dB)

    100

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    0.1

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    475 x 387 x 140

  • Gewicht (kg)

    20.4

  • Offizieller Link