Hifiverse

Endstufen Mono - Accuphase A-300

Beschreibung, Bilder, technische Daten und Spezifikationen

Accuphase A-300
Bildquelle - (c) Accuphase

The A-300 is a Class A monophonic power amplifier from Accuphase of Japan, created to mark the company's 50th anniversary. One chassis drives one channel, so a stereo system needs a pair. Two pairs of A-300 can be used for bi-amping or in bridged mode.

Key specs that matter

Rated output (20 Hz - 20 kHz, 0.05% THD) is 125 W into 8 ohms, with 250 W into 4 ohms and 500 W into 2 ohms for music signals. Maximum output is 1,000 W into 1 ohm. Bridged, it is 500 W into 8 ohms and 1,000 W into 4 ohms (music signals). THD is 0.03% into 4 - 16 ohms, and intermodulation distortion is 0.01%. Frequency response is 20 Hz - 20 kHz (+0, -0.2 dB) at rated output and 0.5 Hz - 160 kHz (+0, -3 dB) at 1 W. Damping factor is 1,000 or greater. Gain is 28, 25, 22 or 16 dB in four steps. Input impedance is 40 kilohms balanced and 20 kilohms on the line input. Signal-to-noise ratio is 130 dB (A-weighted, gain at MAX). Idle consumption is 230 W. Each unit measures 465 x 240 x 515 mm (W x H x D) and weighs 46.0 kg.

Engineering and use context

Its output stage uses 20 parallel push-pull power MOSFETs driven in Class A. Accuphase quotes a 25% performance gain for this stage over its conventional models.

Inside the signal input section, a fully discrete balanced amplifier works on the instrumentation amplifier principle, with equal input impedance on the + and - sides. A high gain of 12.6x is assigned to this section. Amplification follows a current feedback topology, and switching the gain has almost no effect on frequency response. Accuphase uses two MCS+ (Multiple Circuit Summing-up) circuits, a Double MCS+ configuration in which the voltage amplification stage is laid out in two parallel circuits to lower the noise floor.

Balanced remote sensing feeds back the ground together with the signal from the speaker terminals. Protection at the output uses MOSFET switches with no mechanical contacts and guards against short circuits, and edgewise coils are used for the damping factor. A large toroidal transformer and 100,000 µF of filtering capacitance make up the power supply. The power amplification section sits on glass cloth fluorocarbon resin circuit boards, and the feet are high-carbon cast iron insulators.

On the front are a bar graph meter and a digital power meter with switchable display range and hold time. A sub panel holds the gain, LINE/BALANCED input and balanced polarity selectors, and the 230 V version has an Eco Mode.

Pairing

A preamplifier with balanced or RCA outputs is required. The speaker terminals accept spade lugs from 6.3 to 19 mm. Bridged operation needs two A-300 per channel.

Alternatives

The A-80 is Accuphase's Class A stereo power amplifier.

Spezifikationen

  • Modellbezeichnung

    A-300

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Maximaler Strom (A)

    N/A

  • Ausgangsleistung (8Ω) (W)

    125

  • Ausgangsleistung (4Ω) (W)

    250

  • Verstärkung (dBu)

    3, 6, 12

  • Untere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Obere Grenzfrequenz +/- 3dB (Hz)

    N/A

  • Signal-Rausch-Abstand (dB)

    N/A

  • Klirrfaktor + Rauschen (0% Gegenkopplung) (%)

    N/A

  • Klirrfaktor + Rauschen (100% Gegenkopplung) (%)

    N/A

  • Maximale Leistungsaufnahme (W)

    N/A

  • Dämpfungsfaktor

    1000

  • Abmessungen (mm)

    515 x 465 x 240

  • Gewicht (kg)

    46.0

  • Offizieller Link