Hifiverse

Vollverstärker - Cary Audio SLI-100

Beschreibung, Bilder, technische Daten und Spezifikationen

Cary Audio SLI-100
Bildquelle - (c) Cary Audio

The SLI-100 is a stereo tube integrated amplifier from Cary Audio of North Carolina, introduced in October 2018 at USD 5,995. Cary presents it as the more powerful sibling of the SLI-80HS, with KT150 output tubes. The circuit is push-pull ultra-linear in pure class AB1, and wiring is hand-assembled.

Key specs that matter

Power output is 100 W per channel. The tube complement is two 6922 input buffer preamp tubes, two 6SN7 pre-driver and phase inverter tubes and four KT150 output tubes. Input sensitivity is 0.45 V for full output, input impedance is 100 kohms and maximum gain is 34 dB. Frequency response is 19 Hz - 23 kHz (±0.5 dB at full power output), and noise and hum are 82 dB below rated output. Inputs are four pairs of single-ended RCA. Power consumption is 166 W in operation and 83 W in standby. Dimensions are 198 x 438 x 406 mm (H x W x D), and weight is 19 kg.

Engineering and use context

The 6922 input stage is direct coupled to the volume control, and Cary uses no coupling capacitors in the input signal path. Next comes a Series Regulated Push-Pull (SRPP) class A triode voltage amplification stage, direct coupled to a self-balancing split-load phase inverter using the 6SN7 octal dual triode. The KT150s run from a negative fixed bias supply. Bias is factory preset to 75 - 85 mA and can be checked through a bias meter jack.

Cary calls the output transformers the most important component in the amplifier, designed specifically for the SLI-100. Only 4 dB of negative feedback is applied, derived from the secondary at its 8 ohm tap, to lower the noise floor and improve speaker damping. Output polarity is non-inverting on any input. A 200% duty cycle EI laminate power transformer is used. Its subwoofer output is derived from the volume control wiper. A front-panel button switches the signal to the 6.35 mm headphone jack, and the IR remote controls volume and mute. A removable cage cover is standard. The chassis is black powder-coated matte, with a silver or black aluminium faceplate and knobs. Cary lists about 3 minutes before operation after power-on, and break-in is 100 hours of playing time.

Pairing

A switch selects the 4 or 8 ohm output tap to match the loudspeaker impedance. A turntable needs an external phono stage. The full-range subwoofer output also accepts an additional power amplifier.

Alternatives

The Cary Audio SLI-80HS is the lower-powered tube integrated amplifier in the same family.

Spezifikationen

  • Modellbezeichnung

    SLI-100

  • Typ

    Integrated Amplifier

  • Analogeingänge (symmetrisch)

    N/A

  • Analogeingänge (unsymmetrisch)

    4

  • Eingangsempfindlichkeit (mV)

    450

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    100 000

  • Ausgangsimpedanz (symmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • D/A-Wandlung

    k. A.

  • Phono MM/MC-Eingangsimpedanz (stromgekoppelt) (Ω)

    N/A

  • Ausgangsleistung (8Ω) (W)

    100

  • Ausgangsleistung (4Ω) (W)

    100

  • Verstärkung (dBu)

    34

  • Untere Grenzfrequenz +/- 3dB (Hz)

    19

  • Obere Grenzfrequenz +/- 3dB (Hz)

    23 000

  • Signal-Rausch-Abstand (dB)

    N/A

  • Klirrfaktor + Rauschen (%)

    N/A

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    178 x 432 x 406

  • Gewicht (kg)

    19.1

  • Offizieller Link

Weitere Komponenten