Hifiverse

Vollverstärker - Wattson Audio Madison AMPLIFIER

Beschreibung, Bilder, technische Daten und Spezifikationen

Wattson Audio Madison AMPLIFIER
Bildquelle - (c) Wattson Audio

The Madison Amplifier is a 2-channel power amplifier from Wattson Audio of Switzerland, a CH Precision company. It was released on 6 April 2025 at about USD 6,500 or EUR 6,495. Wattson developed it in direct engineering collaboration with CH Precision, covering topology, power strategy and device selection. There is no volume control on board, and the amplifier works in stereo, mono or bi-amp mode.

Key specs that matter

Output power in stereo or bi-amp mode is 2 x 50 W into 8 ohms, 2 x 75 W into 4 ohms and 2 x 100 W into 2 ohms. Bridged to mono it gives 50 W into 8 ohms, 100 W into 4 ohms and 150 W into 2 ohms. Voltage gain is switchable between +20 dB and +26 dB, with an input impedance of 100 kOhm and a nominal input level of 2.0 V RMS. Bandwidth is 1 Hz - 400 kHz (-3 dB), signal-to-noise ratio is more than 120 dB (A-weighted) and THD+N is below 0.05%. Dimensions are 216 x 300 x 87 mm (W x D x H) and weight is 6.0 kg, in Light Gray or Dark Gray.

Engineering and use context

Wattson combines a low-feedback Class A/B linear circuit with a fully symmetrical discrete amplification stage. From the input stage onward the circuit stays fully symmetrical and fully discrete, whether the signal arrives balanced or single-ended. Its output stage uses the same bipolar output devices as the CH Precision M10 Reference Amplifier, one device per rail. Its design uses a low part count and short signal paths.

Power comes from an external balanced, regulated and filtered switch-mode supply with high current capacity, rated at 36 V DC and 350 W with universal input. Consumption is below 0.5 W in standby, 20 W at idle and 450 W at maximum. The chassis is machined from solid billet aluminium and is both the structural frame and the heat management system, and production in Switzerland reuses aluminium off-cuts.

In mono mode a single chassis is assigned to one channel for more output into lower impedances. Bi-amp mode directs the two channels to separate driver sections of one loudspeaker. Rear toggle switches set mode, impedance and gain, front push buttons select input, mute and standby, and firmware is updated over Ethernet.

Pairing

A preamplifier or a source with variable output is required. Inputs are balanced XLR and single-ended RCA, and speaker outputs take spades or bananas. The matching source is the Madison Streamer.

Alternatives

Wattson Audio lists no other stereo power amplifier in its range.

Spezifikationen

  • Modellbezeichnung

    Madison AMPLIFIER

  • Typ

    integrated amplifier

  • Analogeingänge (symmetrisch)

    N/A

  • Analogeingänge (unsymmetrisch)

    N/A

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    N/A

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    100000

  • Ausgangsimpedanz (symmetrisch) (Ω)

    100000

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • D/A-Wandlung

    k. A.

  • Phono MM/MC-Eingangsimpedanz (stromgekoppelt) (Ω)

    N/A

  • Ausgangsleistung (8Ω) (W)

    2 x 50

  • Ausgangsleistung (4Ω) (W)

    2 x 75

  • Verstärkung (dBu)

    N/A

  • Untere Grenzfrequenz +/- 3dB (Hz)

    1

  • Obere Grenzfrequenz +/- 3dB (Hz)

    400000

  • Signal-Rausch-Abstand (dB)

    120

  • Klirrfaktor + Rauschen (%)

    0.05

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    216 x 300 x 87

  • Gewicht (kg)

    6

  • Offizieller Link