Hifiverse

Vollverstärker - Vinnie Rossi BRAMA G2 Integrated Amplifier

Beschreibung, Bilder, technische Daten und Spezifikationen

Vinnie Rossi BRAMA G2 Integrated Amplifier
Bildquelle - (c) Vinnie Rossi

The BRAMA G2 Integrated Amplifier is a hybrid integrated amplifier from VinnieRossi of Worcester, Massachusetts, with a 300B tube linestage and a MOSFET power stage in one chassis. Vinnie Rossi founded the company in 2004 as Red Wine Audio and renamed it after himself around 2014. The second-generation BRAMA collection was announced on 3 April 2024 and shown at AXPONA 2024, and the integrated amplifier became available in May 2024 at USD 47,995. Each unit is hand-assembled and tested in-house.

Key specs that matter

Output power is 200 W RMS per channel into 8 ohms and 400 W RMS into 4 ohms, with stability into 2 ohm loads. THD+N is below 0.1% (20 Hz - 20 kHz), frequency response is 5 Hz - 100 kHz (±0.5 dB), and signal-to-noise ratio is above 100 dB. Inputs are five balanced XLR line inputs with 20 kOhm input impedance, and RCA-to-XLR adapters are included. Gain settings are 22 dB (low), 28 dB (med) and 34 dB (high). A volume-controlled XLR line output is provided. Dimensions are 475 x 406 x 140 mm, and weight is 22.7 kg.

Engineering and use context

A matched pair of Western Electric WE300B triodes operates in a dual mono Class A linestage that provides voltage gain only. Both tubes sit horizontally inside the chassis in Teflon sockets, mounted to the rear panel together with the dual-mono preamplifier board. VinnieRossi states that, without output power duty, the 300Bs run cooler and last 10 years or more.

Its power amplifier stage is a two-PCB stack. The upper board carries the fully balanced input and driver stages, and the lower board holds the Class AB output stage with two computer-matched lateral MOSFETs per rail, mounted directly to the chassis.

Power comes from a switch-mode supply with active power factor correction, rated at 2400 W peak, in its own CNC-machined chamber. The linestage section uses patented Belleson linear super-regulators. Its chassis is machined on a 5-axis CNC machine from a single billet of AL6063 aluminium alloy, then bead-blasted and anodized.

Volume is a 100-step resistor ladder, balance has 12 steps, and gain and balance are memorised per input. A Home Theater Bypass mode is provided. The right knob is a 48-position Swiss rotary encoder with magnetic sensing and push-to-mute, and a wattage gauge under a sapphire lens shows RMS watts into 8 and 4 ohms. Speaker outputs are WBT nextgen 0710-Ag binding posts. The remote is milled from solid aluminium and uses Bluetooth.

Pairing

The Brama Link output provides a trigger or a direct interface with BRAMA monoblocks. Its XLR line output allows a powered subwoofer or an external power amplifier.

Alternatives

The CANTA Integrated is the other hybrid integrated amplifier from VinnieRossi, in the CANTA series.

Spezifikationen

  • Modellbezeichnung

    BRAMA Integrated Amplifier

  • Typ

    Integrated amplifier

  • Analogeingänge (symmetrisch)

    5

  • Analogeingänge (unsymmetrisch)

    N/A

  • Eingangsempfindlichkeit (mV)

    N/A

  • Eingangsimpedanz (symmetrisch) (Ω)

    20000

  • Eingangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • Ausgangsimpedanz (symmetrisch) (Ω)

    100

  • Ausgangsimpedanz (unsymmetrisch) (Ω)

    N/A

  • D/A-Wandlung

    k. A.

  • Phono MM/MC-Eingangsimpedanz (stromgekoppelt) (Ω)

    N/A

  • Ausgangsleistung (8Ω) (W)

    2 x 200

  • Ausgangsleistung (4Ω) (W)

    2 x 400

  • Verstärkung (dBu)

    22, 28, 34

  • Untere Grenzfrequenz +/- 3dB (Hz)

    5

  • Obere Grenzfrequenz +/- 3dB (Hz)

    100000

  • Signal-Rausch-Abstand (dB)

    100

  • Klirrfaktor + Rauschen (%)

    0.1

  • Dämpfungsfaktor

    N/A

  • Abmessungen (mm)

    475 x 406 x 140

  • Gewicht (kg)

    22.7

  • Offizieller Link

Weitere Komponenten